View ADCMP671_4465895.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

low power, adjustable uv and ov monitor with 400 mv, 0.275% reference data sheet ADCMP671 rev. 0 information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2011 analog devices, inc. all rights reserved. features window monitoring with minimum processor i/o individually monitoring n rails with only n + 1 processor i/o 400 mv , 0.275% threshold at v dd = 3.3 v, 25c supp ly range: 1.7 v to 5.5 v low quiescent current: 17 a maximum at 125c input range includes ground internal hysteresis: 9.2 mv typical low input bias current: 2.5 na maximum open-drain outputs power good indication output designated over voltage indication output low profile (1 mm), 6-lead tsot package applications supply voltage monitoring li-ion monitoring portable applications handheld instruments functional block diagram inh uv ov inl v dd gnd 400mv ADCMP671 pwrgd ov 10160-001 figure 1. general description the ADCMP671 voltage monitor consists of two low power, high accuracy comparators and reference circuits. it operates on a supply voltage from 1.7 v to 5.5 v and draws 17 a maximum, making it suitable for low power system monitoring and portable applications. the part is designed to monitor and report supply undervoltage and overvoltage fault. the low input bias current and voltage reference allows resistor adjustable uv and ov threshold down to 400 mv. the ADCMP671 has two open- drain outputs: the pwrgd output indicates that the supply is within the uv and ov window, and the ov output indicates that the supply is overvoltage. this output combination allows users to window monitor n supplies with an n + 1 processor input/output (i/o). each output is guaranteed to sink greater than 5 ma over temperature. the ADCMP671 is available in 6-lead tsot package. the device operates over the ?40c to +125c temperature range. 386 threshold voltage (mv) temperature (c) ?40 ?20 0 20 40 60 80 100 120 404 402 400 398 396 394 392 390 388 rising input falling input inl2 inh2 inl1 inh1 two typical parts comparator a and comparator b v dd = 5v 10160-002 figure 2. comparator thresholds vs. temperature
ADCMP671 data sheet rev. 0 | page 2 of 16 table of contents features .............................................................................................. 1 ? applications....................................................................................... 1 ? functional block diagram .............................................................. 1 ? general description ......................................................................... 1 ? revision history ............................................................................... 2 ? specifications..................................................................................... 3 ? absolute maximum ratings............................................................ 7 ? thermal resistance ...................................................................... 7 ? esd caution.................................................................................. 7 ? pin configuration and function descriptions............................. 8 ? typical performance characteristics ..............................................9 ? applications information .............................................................. 14 ? comparators and internal reference ...................................... 14 ? power supply............................................................................... 14 ? inputs ........................................................................................... 14 ? hysteresis..................................................................................... 14 ? voltage monitoring scheme ..................................................... 14 ? outputs ........................................................................................ 15 ? outline dimensions ....................................................................... 16 ? ordering guide .......................................................................... 16 ? revision history 11/11revision 0: initial version
data sheet ADCMP671 rev. 0 | page 3 of 16 specifications v dd = 1.7 v to 5.5 v, t a = 25c, unless otherwise noted. table 1. parameter min typ max unit test conditions/comments thresholds 1 rising input threshold voltage (v th(r) ) 396.6 400.4 404.3 mv v dd = 1.7 v 399.3 400.4 401.5 mv v dd = 3.3 v 398.5 400.4 402.2 mv v dd = 5.5 v falling input threshold voltage(v th(f) ) 387 391 395.4 mv v dd = 1.7 v 389.2 391 392.9 mv v dd = 3.3 v 388.5 391 393.2 mv v dd = 5.5 v rising input threshold voltage accuracy 0.275 % v dd = 3.3 v falling input threshold voltage accuracy 0.475 % v dd = 3.3 v hysteresis = v th(r) ? v th(f) 7.8 9.2 11.1 mv input characteristics input bias current 0.01 1 na v dd = 1.7 v, v in = v dd 0.01 1 na v dd = 1.7 v, v in = 0.1 v open-dran outputs output low voltage 2 140 200 mv v dd = 1.7 v, i out = 3 ma 130 200 mv v dd = 5.5 v, i out = 5 ma output leakage current 3 0.01 0.1 a v dd = 1.7 v, v out = v dd 0.01 0.1 a v dd = 1.7 v, v out = 5.5 v dynamic performance 2 , 4 high-to-low propagation delay 10 s v dd = 5.5 v, v ol = 400 mv low-to-high propagation delay 8 s v dd = 5.5 v, v oh = 0.9 v dd output rise time 0.5 s v dd = 5.5 v, v out = (0.1 to 0.9) v dd output fall time 0.07 s v dd = 5.5 v, v out = (0.1 to 0.9) v dd power supply supply current 5 5.7 10 a v dd = 1.7 v 6.5 11 a v dd = 5.5 v 1 r l = 100 k, v out = 2 v swing. 2 v in = 10 mv input overdrive. 3 v in = 40 mv overdrive. 4 r l = 10 k. 5 no load current.
ADCMP671 data sheet rev. 0 | page 4 of 16 v dd = 1.7 v to 5.5 v, 0c t a 70c, unless otherwise noted. table 2. parameter min typ max unit test conditions/comments thresholds 1 rising input threshold voltage (v th(r) ) 395.3 405.3 mv v dd = 1.7 v 397.3 403.3 mv v dd = 3.3 v 396.8 403.8 mv v dd = 5.5 v falling input threshold voltage (v th(f) ) 385.8 397.3 mv v dd = 1.7 v 386.2 394.8 mv v dd = 3.3 v 385.8 395.2 mv v dd = 5.5 v rising input threshold voltage accuracy 0.75 % v dd = 3.3 v falling input threshold voltage accuracy 1.1 % v dd = 3.3 v hysteresis = v th(r) ? v th(f) 6.8 12.2 mv input characteristics input bias current 1 na v dd = 1.7 v, v in = v dd 1 na v dd = 1.7 v, v in = 0.1 v open-drain outputs output low voltage 2 250 mv v dd = 1.7 v, i out = 3 ma 250 mv v dd = 5.5 v, i out = 5 ma output leakage current 3 0.1 a v dd = 1.7 v, v out = v dd 0.1 a v dd = 1.7 v, v out = 5.5 v power supply supply current 4 13 a v dd = 1.7 v 14 a v dd = 5.5 v 1 r l = 100 k, v out = 2 v swing. 2 v in =10 mv input overdrive. 3 v in = 40 mv overdrive. 4 no load.
data sheet ADCMP671 rev. 0 | page 5 of 16 v dd = 1.7 v to 5.5 v, ?40c t a +85c, unless otherwise noted. table 3. parameter min typ max unit test conditions/comments thresholds 1 rising input threshold voltage (v th(r) ) 391.2 407.8 mv v dd = 1.7 v 393.1 405.9 mv v dd = 3.3 v 393.5 405.4 mv v dd = 5.5 v falling input threshold voltage (v th(f) ) 383.3 400.9 mv v dd = 1.7 v 384.7 398.4 mv v dd = 3.3 v 384.4 398.2 mv v dd = 5.5 v rising input threshold voltage accuracy 1.6 % v dd = 3.3 v falling input threshold voltage accuracy 1.75 % v dd = 3.3 v hysteresis = v th(r) ? v th(f) 5.4 12.6 mv input characteristics input bias current 1 na v dd = 1.7 v, v in = v dd 1 na v dd = 1.7 v, v in = 0.1 v open-drain outputs output low voltage 2 250 mv v dd = 1.7 v, i out = 3 ma 250 mv v dd = 5.5 v, i out = 5 ma output leakage current 3 0.1 a v dd = 1.7 v, v out = v dd 0.1 a v dd = 1.7 v, v out = 5.5 v power supply supply current 4 14 a v dd = 1.7 v 15 a v dd = 5.5 v 1 r l = 100 k, v out = 2 v swing. 2 v in = 10 mv input overdrive. 3 v in = 40 mv overdrive. 4 no load.
ADCMP671 data sheet rev. 0 | page 6 of 16 v dd = 1.7 v to 5.5 v, ?40c t a +125c, unless otherwise noted. table 4. parameter min typ max unit test conditions/comments thresholds 1 rising input threshold voltage (v th(r) ) 391.2 407.8 mv v dd = 1.7 v 393.1 405.9 mv v dd = 3.3 v 393.1 405.8 mv v dd = 5.5 v falling input threshold voltage (v th(f) ) 381.1 400.9 mv v dd = 1.7 v 381.2 398.4 mv v dd = 3.3 v 381 398.2 mv v dd = 5.5 v rising input threshold voltage accuracy 1.6 % v dd = 3.3 v falling input threshold voltage accuracy 2.2 % v dd = 3.3 v hysteresis = v th(r) ? v th(f) 5.4 13.5 mv input characteristics input bias current 2.5 na v dd = 1.7 v, v in = v dd 2.5 na v dd = 1.7 v, v in = 0.1 v open-drain outputs output low voltage 2 250 mv v dd = 1.7 v, i out = 3 ma 250 mv v dd = 5.5 v, i out = 5 ma output leakage current 3 0.1 a v dd = 1.7 v, v out = v dd 0.1 a v dd = 1.7 v, v out = 5.5 v power supply supply current 4 16 a v dd = 1.7 v 17 a v dd = 5.5 v 1 r l = 100 k, v out = 2 v swing. 2 v in = 10 mv input overdrive. 3 v in = 40 mv overdrive. 4 no load.
data sheet ADCMP671 rev. 0 | page 7 of 16 absolute maximum ratings table 5. parameter rating v dd ?0.3 v to +6 v inh, inl ?0.3 v to +6 v ov , pwrgd ?0.3 v to +6 v output short-circuit duration 1 indefinite input current ?10 ma operating temperature range ?40c to +125c storage temperature range ?65c to +150c lead temperature soldering (10 sec) 300c vapor phase (60 sec) 215c infrared (15 sec) 220c 1 when the output is shorted indefinitely, the use of a heat sink may be required to keep the junction temperature within the absolute maximum ratings. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. thermal resistance ja is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. table 6. thermal resistance package type ja unit 6-lead tsot 200 c/w esd caution
ADCMP671 data sheet rev. 0 | page 8 of 16 pin configuration and fu nction descriptions 1 pwrgd 6 ov 2 gnd 5 v dd 3 inh 4 inl ADCMP671 top view (not to scale) 10160-003 figure 3. pin configuration table 7. pin function descriptions pin o. nemonic description 1 pwrgd open-drain active high power good output. it asserts when the input falls within the uv and ov window, for example, inh high and inl low. 2 gnd ground. 3 inh monitors for supply undervoltage fault through an external re sistor divider network. it is internally connected to the noninverting input of a comparator. the other input of the comparator is connected to a 400 mv reference. 4 inl monitors for supply overvoltage fault through an external resi stor divider network. it is internally connected to the inverting input of a comparator. the other input of the comparator is connected to a 400 mv reference. 5 v dd power supply pin. 6 ov open-drain output active low overvoltage fault indication output. it asserts when there is an overvoltage fault, for example, inl high.
data sheet ADCMP671 rev. 0 | page 9 of 16 typical performance characteristics 0 10 20 30 40 50 percent of units (%) rising input threshold voltage (mv) 60 394 395 396 397 398 399 400 401 402 403 404 405 406 v dd = 5v t a = 25c 10160-004 0 10 20 30 40 percent of units (%) falling input threshold voltage (mv) 50 388 389 390 391 392 393 394 395 396 397 398 399 400 v dd = 5v t a = 25c 10160-007 figure 4. distribution of rising input threshold voltage figure 7. distribution of falling input threshold voltage 0 5 10 15 20 25 30 percent of units (%) hysteresis (mv) 35 6.0 6.4 6.8 7.2 7.6 8.0 8.4 8.8 9.2 9.6 10.0 10.4 10.8 v dd = 5v t a = 25c 10160-005 398 rising input threshold voltage (mv) temperature (c) 402 401 400 399 ?40 ?20 120 0 20406080100 v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.8v 10160-008 figure 5. distribution of hysteresis figure 8. rising input threshold voltage vs. temperature for various v dd voltages 396 rising input threshold voltage (mv) temperature (c) 404 402 400 398 ?40 ?20 120 0 20406080100 4 3 2 1 four typical parts v dd = 5v 10160-006 395 rising input threshold voltage (mv) supply voltage (v) 401 400 399 398 397 396 1.7 5.7 5.2 4.7 4.2 3.7 3.2 2.7 2.2 t a = ?40c t a = +25c t a = +85c t a = +125c 10160-009 figure 9. rising input threshold voltage vs. supply voltage figure 6. rising input threshold voltage vs. temperature for four typical parts
ADCMP671 data sheet rev. 0 | page 10 of 16 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 hysteresis (mv) temperature (c) 12.0 ?40 ?20 120 0 20406080100 inl2 inh2 1nl1 1nh1 four typical parts v dd = 5v 10160-010 figure 10. hysteresis vs. temperature for four typical parts 4 5 6 7 8 9 10 11 hysteresis (mv) supply voltage (v) 12 1.7 5.7 5.2 4.7 4.2 3.7 3.2 2.7 2.2 t a = +125c t a = +25c t a = +85c t a = ?40c 10160-011 figure 11. hysteresis vs. supply voltage 10 4 5.2 supply current (a) supply voltage (v) 9 8 7 6 5 1.7 2.2 2.7 3.2 3.7 4.2 4.7 t a = +125c t a = +85c t a = +25c t a = ?40c no load current 10160-012 figure 12. quiescent supply current vs. supply voltage 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 hysteresis (mv) temperature (c) 12.0 ?40 ?20 120 0 20406080100 v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.8v 10160-013 figure 13. hysteresis vs. temperature for various v dd voltages ?5 threshold shift (mv) supply voltage (v) 1 1.5 2.52.4 2.3 2.22.1 2.0 1.91.8 1.7 1.6 t a = +125c t a = +85c t a = +25c t a = ?40c 0 ?1 ?2 ?3 ?4 10160-014 figure 14. minimum supply voltage 50 0 1.5 supply current (a) supply voltage (v) 40 30 20 10 00 . 51 . 0 t a = +125c t a = +85c t a = +25c t a = ?40c 10160-015 figure 15. start-up supply current
data sheet ADCMP671 rev. 0 | page 11 of 16 1 supply current (a) output sink current (ma) 1000 100 10 0.001 100 10 1 0.1 0.01 t a = ?40c v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.7v 10160-016 figure 16. supply current vs. output sink current for t a = ?40c 1 supply current (a) output sink current (ma) 1000 100 10 0.001 100 10 1 0.1 0.01 v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.7v t a = 85c 10160-018 figure 17 . supply current vs. output sink current for t a = 85c ?7 1.0 input bias current (na) input voltage (v) ?3 ?5 00 . 2 0 .6 ?1 3 1 0.4 0.8 t a = +125c t a = +85c t a = +25c t a = ?40c current is positive going into the device v dd = 5v 0v < v ib < 1v 10160-020 figure 18. low level input bias current vs. input voltage 1 supply current (a) output sink current (ma) 1000 100 10 0.001 100 10 1 0.1 0.01 v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.7v t a = 25c 10160-017 figure 19. supply current vs. output sink current for t a = 25c 0.1 0 input bias current (na) input voltage (v) 1k 10k 100 10 1 ?0.3 ?0.2 ?0.1 t a = +125c t a = +85c t a = +25c t a = ?40c current is going out of the device. v dd = 5v ?0.3v < v ib < 0v 10160-019 figure 20. below ground input bias current vs. input voltage 0.01 5 input bias current (na) input voltage (v) 1 0.1 12 4 10 3 t a = ?40c t a = +125c t a = +85c t a = +25c current is going into the device v dd = 5v v ib > 1v 10160-021 figure 21. high level input bias current vs. input voltage
ADCMP671 data sheet rev. 0 | page 12 of 16 1 output saturation voltage (mv) output sink current (ma) 100 10 0.001 0.1 0.01 1000 10 1 v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.8v t a = 25c 10160-022 figure 22. output saturation voltage vs. output sink current for t a = 25c 1 output saturation voltage (mv) output sink current (ma) 100 10 0.001 0.1 1000 10 0.01 1 v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.8v t a = 85c 10160-024 figure 23. output saturation voltage vs. output sink current for t a = 85c 0 short-circuit current (ma) output voltage (v) 40 20 02 70 4 60 30 10 50 v dd = 5.0v v dd = 3.3v v dd = 2.5v v dd = 1.8v t a = 25c 10160-026 figure 24. output short-circuit current vs. output voltage 1 output saturation voltage (mv) output sink current (ma) 100 10 0.001 0.1 1000 10 0.01 1 v dd = 5.0v t a = ?40c v dd = 3.3v v dd = 2.5v v dd = 1.8v 10160-023 figure 25. output saturation voltage vs. output sink current for t a = ?40c 0 short-circuit current (ma) output voltage (v) 40 20 02 80 4 60 30 10 70 50 t a = +85c t a = +25c t a = +125c t a = ?40c v dd = 5v 10160-025 figure 26. output short-circuit current vs. output voltage 0.001 output leakage current (na) output voltage (v) 0.01 0123 10 45 1 0.1 t a = +125c t a = +85c t a = +25c t a = ?40c v dd = 5v 10160-027 figure 27. output leakage current vs. output voltage
data sheet ADCMP671 rev. 0 | page 13 of 16 0 propagation delay (s) input overdrive (mv) 0 204060 70 60 50 40 30 20 10 80 100 t a = 25c inh lh inl lh inh hl inl hl 10160-028 v dd (v) 5 4 3 2 v out (v) 1 0 5 4 3 2 1 0 pwrgd ov outputs being pulled up to vdd with 10k ? inh = low inl = low 10160-031 figure 28. propagation delay vs. input overdrive figure 31. output voltage vs. supply voltage with both inh and inl low 10160-029 ch3 5.0v ch4 5.0v m40.0s 1 4 3 inl v th(r) inl v th(f) inh v th(r) inh v th(f) pwrgd ov v in r _pullup = 10k ? v _pullup = 5v v dd (v) 5 4 3 2 v out (v) 1 0 5 4 3 2 1 0 pwrgd ov outputs being pulled up to v dd with 10k ? inh = high inl = low 10160-032 figure 29. propagation delay figure 32. output voltage vs. supply voltage with inh high and inl low 0.01 rise and fall times (s) output pull-up resistor (k ? ) 1 0.1 1 100 10 10 0.1 100 1000 rise fall v dd = 5v c l = 20pf t a = 25c 10160-030 v dd (v) 5 4 3 2 v out (v) 1 0 5 4 3 2 1 0 pwrgd ov outputs being pulled up to v dd with 10k ? inh = high inl = high 10160-033 figure 30. rise and fall times vs. output pull-up resistor figure 33. output voltage vs. supply voltage with both inh and inl high
ADCMP671 data sheet rev. 0 | page 14 of 16 applications information the ADCMP671 is a uv and ov monitor with a built-in 400 mv reference that operates from 1.7 v to 5.5 v. the comparator is 0.275% accurate with a built-in hysteresis of 9.2 mv. the outputs are open-drain, capable of sinking 40 ma. comparators and internal reference there are two comparators inside the ADCMP671 . the comparator with its noninverting input connected to the inh pin (and its inverting input connected internally to the 400 mv reference) is for undervoltage detection, and the comparator with its inverting input available through the inl pin (and its noninverting input connected internally to the 400 mv reference) is for overvoltage detection. the rising input threshold voltage of the comparators is designed to be equal to that of the reference. power supply the ADCMP671 is designed to operate from 1.7 v to 5.5 v. a 0.1 f decoupling capacitor is recommended between v dd and gnd. inputs the comparator inputs are limited to the maximum v dd voltage range. the voltage on these inputs can be more than v dd but never more than the maximum allowed v dd voltage. when adding a resistor string to the input, choose resistor values carefully because the input bias current is in parallel with the bottom resistor of the string. therefore, choose the bottom resistor first to control the error introduced by the bias current. to minimize the number of external components use three resistor dividers to program the uv and ov thresholds. hysteresis to prevent oscillations at the output caused by noise or slowly moving signals passing the switching threshold, each comparator has a built-in hysteresis of approximately 8.9 mv. voltage monitoring scheme when monitoring a supply rail, the desired nominal operating voltage for monitoring is denoted by v m , i m is the nominal current through the resistor divider, v ov is the overvoltage trip point, and v uv is the undervoltage trip point. figure 34 illustrates the voltage monitoring input connection. three external resistors, r x , r y , and r z , divide the positive voltage for monitoring (v m ) into the high-side voltage (v h ) and low- side voltage (v l ). the high-side voltage is connected to the inh pin, and the low-side voltage is connected to the inl pin. inh uv ov inl v dd gnd 12 v r x r y r z 5 v 400mv ADCMP671 pwrgd ov 10160-034 figure 34. undervoltage/overvol tage monitoring configuration to trigger an overvoltage condition, the low-side voltage (in this case, v l ) must exceed the 0.4 v threshold on the inl pin. the low-side voltage, v l , is given by the following equation: v4.0 = ? ? ? ? ? ? ? ? ++ = z yx z ov l rrr r vv also, m m z yx i v rrr =++ therefore, r z , which sets the desired trip point for the overvoltage monitor, is calculated using the following equation: ( ) () () m ov m z iv v r )4.0( = to trigger the undervoltage condition, the high-side voltage, v h , must fall below the 0.4 v threshold on the inh pin. the high- side voltage, v h , is given by the following equation: v4.0 = ? ? ? ? ? ? ? ? ++ + = z yx z y uvh rrr rr vv because r z is already known, r y can be expressed as follows: ( ) () () z muv m y r iv v r ? = )4.0( when r y and r z are known, r x is calculated using the following equation: ( ) () y z m m x rr i v r ??= if v m , i m , v ov , or v uv changes each step must be recalculated.
data sheet ADCMP671 rev. 0 | page 15 of 16 outputs the pwrgd output is used to indicate supply power good for the rail being monitored. it asserts if the monitored voltage falls within the uv and ov threshold window. the ov output acts as a dedicated overvoltage indication output, allows the board manager to take decisive action to protect the system from overvoltage faults. both outputs are open-drain and can be pulled up to voltages above v dd . these outputs are capable of sinking current up to 40 ma. in the multisupply monitoring application, multiple ADCMP671 can be used with their ov pin tied together to generate a single overvoltage fault alert signal, as shown in . during power up and power down, the power management processor of the board can manage supply sequencing based on pwrgd signals. in the event of supply overvoltage fault, the processor can react quickly to the provide necessary circuit protection because of its dedicated figure 35 ov alert. the processor is also able to identify the faulty supply from combining the information on the pwrgd pins. this allows the processor to use the n + 1 input pins to individually monitor n channels of supplies. 2.5v pwrgd ov 2.5v good 1.8v good 1.0v good 0.9v good ov fault board manager ADCMP671 1.8v pwrgd ov ADCMP671 1.0v pwrgd ov ADCMP671 0.9v pwrgd ov ADCMP671 10160-035 figure 35. n rails monitoring with n + 1 processor i/o
ADCMP671 data sheet rev. 0 | page 16 of 16 outline dimensions 102808-a * compliant to jedec standards mo-193-aa with the exception of package height and thickness. 13 45 2 6 2.90 bsc 1.60 bsc 2.80 bsc 1.90 bsc 0.95 bsc 0.10 max * 1.00 max pin 1 indicator * 0.90 0.87 0.84 0.60 0.45 0.30 0.50 0.30 0.20 0.08 seating plane 8 4 0 figure 36. 6-lead thin small outline transistor package [tsot] (uj-6) dimensions shown in millimeters ordering guide model 1 temperature range package description package option branding ADCMP671-1yujz-rl7 ?40c to +125c 6-lead thin sm all outline transistor package [tsot] uj-6 lls 1 z = rohs compliant part. ?2011 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. d10160-0-11/11(0)

▲Up To Search▲

Price & Availability of ADCMP671

	To Download ADCMP671 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .